Wavlink AC1200 Wifi Extender Setup

Do you favour using wifi.wavlink.com to set up a Wavlink WiFi extender? Don't get alarmed in that scenario! You've come to the right place. Using a Wavlink AC1200 WiFi Extender Setup, you may quickly boost the wireless extender speed and restore lost wireless network signals.You can extend the wireless signal coverage in your home or place of business with this extension device. Read this topic in its entirety if you're setting up a wavlink range extender for the first time and are unsure of what to do. Here are the straightforward instructions for installing a Wavlink range extender.

 

Installation of Wavlink AC1200 Extender

 

1. Activate the wavlink ac1200 extender.
2. Keep your extender close to the LAN router at home.
3. Please visit ap.setup.
4. Then choose NEW EXTENDER SETUP.
5. To continue, adhere to all of the on-screen directions.
6. Once it is finished, move your AC1200 to the new position of your choice.
7. You can now join the network with your other smart devices.

 

Note:- For more information regarding wavlink wifi extender feel free and contact our technician or visit the official website that is ap.setup.

 

 

Wavlink wifi extender setup via manual method

1. Connect the extender to a power outlet.
2. Once the range extender is turned on by a power LED
3. any smart device, and then (i.e., mobile phone, tablet, computer, etc.)
4. Go to the wifi settings in the settings menu on your smart device.
5. Tap the "Wavlink-Extender Setup Ext" connection.
6. Open your mobile device's web browser after you're connected.
7. On the link bar, type the address as it is set up.
8. Range extender's new setup page will load.
9. To set up the extender, refer to the detailed instructions.

 

Wavlink extender setup via WPS method

 

the steps below to configure your wavlink ac1200 utilising WPS:

 

●     Unbox your Wavlink WiFi extender and then turn it on.

●     Put your ac1200 close to your primary router.

●     The extender's WPS button should be pressed.

●     Press the WPS button on the router after a brief delay.

●     If the router LED doesn't become solid green after a minute, give our technical team a call.

●     When it flashes a solid green light, your setup procedure is over.

●     Place your Wavlink WiFi extender at the new position of your choice.

●     All WiFi-enabled smart devices, such as a tablet, laptop, desktop, or smartphone, can now be connected.

 

Wavlink ac1200 extender Troubleshooting steps

 

1. The WPS button is by default disabled on some IP 192.168.10.1 gateways. If you are unable to connect using the WPS button, you can configure your extender by visiting the Wavlink wifi extender setup management website.
2. Ensure that the extender's chosen position is close to your wireless router.
3. If not, there will be a noticeable performance difference on your improved network. Keep it at least one meter away from your router.
4. Ensure that the location of your connection is far from any electronic interference devices.Using Bluetooth-enabled appliances such as cordless phones, microwaves, and baby monitors is not recommended.

 

Reset you Wavlink extender setup

 

Do you desire to restart your Wavlink AC1200 WiFi Extender? The majority of the time, when the user is unable to recall the admin password, a factory reset procedure is intended to be carried out. This procedure will get your extender ready for a new installation. Remember that performing a factory reset will remove all of your customised settings, including your username, password.

 

Reset your  wavlink AC1200 WiFi Extender by following the instructions below:

 

1. Turn on and plug in your  Wavlink AC1200.
2. Wait until the light turns a stable, solid green.
3. Find the hole for the factory reset.
4. It might be accessible from the extender's side.
5. Grab a strong pin or paper clip.
6. Place the paper clip or pin in the hole and keep it there for 8 to 10 seconds.
7. When the power light turns solid green, remove the paper clip.