How do I connect my Victony AC1200 WiFi Extender?

John Show
By -
0

AC1200 WiFi Extender

 Do you prefer the Victony AC1200 WiFi extender setup via ap.setup? In the situation, don't panic! You've arrived at the proper location. You may easily increase the wireless extender speed and recover lost wireless network signals by using a Victony AC1200 WiFi Extender Setup. You may extend the wireless signal's range across your home or place of business with the aid of this device. If you're putting up a Victony range extender for the first time and are uncertain of what to do, read this subject in its entirety. Here are the simple steps for setting up a Victony range extender.

 

Victony AC1200 Extender Installation

 

        Turn on your ac1200 wifi extender.

        Keep your home's LAN router and extension close to each other.

        Visit ap.setup right now.

        Afterward, choose NEW EXTENDER SETUP.

        Follow all of the instructions displayed on the screen to proceed.

        Move your AC1200 to the new location of your choosing after it is done.

        Your additional smart gadgets can now join the network.

 

How do I manually install a wifi extender?

 

  1. Connect the power outlet to the extender.
  2. Once a power LED on any smart device turns on the range extender (i.e., mobile phone, tablet, computer, etc.)
  3. Navigate to your smart device's settings menu and choose WiFi.
  4. On the connection, click "Victony-Extender Setup Ext."
  5. Once you're connected, launch the web browser on your mobile device.
  6. Enter the address exactly as it is set up in the link bar.
  7. The range extender's new setup page will launch.
  8. Refer to the detailed instructions to set up the extender.

 

Note:- If you need any help regarding your Victony wifi extender so contact our technician or visit the official website that is ap wifi range extender setup.

 

Wps setup for Victony ac1200 wifi extender?

 

To configure your Victony AC1200 using WPS, follow these steps:

 

        Open the package containing your Victony WiFi extender, then switch it on.

        Your ac1200 should indeed be placed close to your main router.

        The WPS button on the extender has to be depressed.

        After a little wait, press the WPS button on the router.

 

        Give our technical team a call if the router LED doesn't become solid green after a minute.

 

Victony AC1200 Extender is not working

 

        On some IP 192.168.10.1 gateways, the WPS button is by default deactivated. Visit the Victony wifi extender setup management website to set up your extender if you are unable to connect using the WPS button.

        Make certain that the extender is placed close to your wireless router.

        If not, your upgraded network will experience a considerable performance change. It should be at least one meter away from your router.

        Away from any electrical interference gadgets should be where you are connecting.

        It is not advised to use Bluetooth-enabled devices including cordless phones, microwaves, and baby monitors.

 

How do I Reset my VictonyWi-Fi Extender?

 

Does your Victony AC1200 WiFi Extender need to be restarted?A factory reset procedure is typically done when the user is unable to remember the admin password.Your extender will be ready for a fresh installation when you complete this process. Keep in mind that a factory reset will eliminate all of your customised settings, especially your account and password.

 

In order to reset your Victony AC1200 WiFi Extender, follow these steps:

 

        Start up your Victony AC1200 after plugging it in.

        Hold off until the green light becomes steady and firm.

        Locate the factory reset hole.

        It could be reachable from the side of the extender.

        Grab a sturdy paper clip or pin.

        In the hole, insert the paper clip or pin, and hold it there for 8 to 10 seconds.

        Remove the paper clip when the power light is solid green.

 

 

 

Post a Comment

0Comments

Post a Comment (0)

#buttons=(Ok, Go it!) #days=(20)

Our website uses cookies to enhance your experience. Learn more
Ok, Go it!